Muxpro Series

Ethernet over SDH

MUXpro Series's STM-1 standard main link provides 1+1 dedicated protection in point to point constellation. On board E1(820/8216 only) / Ethernet interfaces design allows MUXpro Series integrate IP/ TDM service. Applications like Ethernet leased line, Inter POP services and transportation for Mobile voice/ Data networks could be refined over existing Infrastructure. Furthermore, MUXpro Series can be managed easily through Web interface, IP over DCC, VC-12 channels, telnet and Tainet Universal NMS.

.Using GFP (ITU-T G.7041) or LAPS (ITU-T X.85/86) encapsulation transport Ethernet over SDH
.Link Capacity Adjustment Scheme (LCAS) compliance with ITU-T G.7042 for seamless bandwidth control
Support VC-3/VC-12 cross connect mapping 
High order payload with virtual concatenation - mapping the Ethernet traffic over up to 1 x VC-4 links 
Low order payload with virtual concatenation - mapping the Ethernet traffic over up to 63 x VC-12 /3 x VC-3 
GFP Mux, groom multiple 
Ethernet ports traffic into different bundles of Virtual Containers, (up to 6 bundles) Ethernet Line-Service (Point to Point) and Ethernet LAN-Service (Multipoint to Multipoint) 
System clock synchronization from primary internal clock and secondary clock from STM-1 or tributary (820/8216 only) 
Configurable through user friendly Web-Interface 
Manage remote units via dedicated VC-12 channel or DCC channel 
Selectable DCC channels: D1~D3, D4~D12, D1~D12
System
-Using GFP (according to G.7041) or LAPS (X.85/86) encapsulation transport Ethernet over SDH, comply with G.707
-Link Capacity Adjustment Scheme (LCAS) following G.7042 standard.
-Support VC-3/VC-12 cross connect mapping
-High order payload with virtual concatenation – mapping the Ethernet traffic over up to 1xVC-4 links
-Low order payload with virtual concatenation – mapping the Ethernet traffic over up to 63 x VC -12 / 3 x VC-3
-GFP MUX, groom multiple Ethernet ports traffic into different bundles of Virtual Containers (up to 6 bundles), according to a predefined group
-Ethernet Line-Service (Point to Point) and Ethernet LAN-Service (Multipoint to Multipoint)
-System clock synchronization from primary internal clock; secondary clock from STM-1 or tributary
-Configurable through user friendly Web-Interface
-Manage remote unit via dedicated VC-12 channel or DCC channel
-Selectable DCC channels: D1~D3, D4~D12, D1~D12
 
Layer 2 Bridge / Switch Mode
-Support bridge function for LAN1~LAN4
-IGMP snooping
-Spanning Tree Protocol (STP IEEE 802.1D) and status monitoring
-QoS (VLAN or DSCP selection) via four priority queues, supporting IEEE 802.1P, IPv4 TOS / DiffServ
-Provide port-based VLAN, 802.1Q VLAN tagging up to 64 VLAN IDs
-Switch mode supports Ethernet packet length up to 1536 bytes
 
Transmission Mode
-8 E1 links + 6 Fast Ethernet
 
Interfaces
 
-STM-1 Interface:
Number of ports: 2, 1+1 MSP protection available
Framing: SDH
Bit Rate: 155.520Mbps
Jitter Performance: compliant with ITU-T G.783
Optical Wavelength: 1310nm
Optical output power: -6dBm
Receiver sensitivity: -34dBm
Connectors: SC or FC/PC
 
-LAN Interface:
Number of ports: 6
Port 1 to 4 support VLAN while Port 5 and 6 do not
Ethernet Type: 10/100 Base T, auto sensing/auto negotiation
Compliance Protocol: IEEE802.3u, 802.3x
Connectors: shielded, RJ45.
 
-ITU-T G.703 E1 Interface:
Number of ports: 8 or 16
Line Rate: 2.048Mbps
Line Coding: HDB3
Jitter Performance: compliant with ITU-T G.823, see Appendix I.
Connector: SCSI II, female
 
Timing Source Setting:
-Provide internal, optical 1, and optical 2, E1 Tributary clock source as system clock
-Recovered clock from STM-1 interface, auto switching in auto mode
-External clock from E1 tributary (2048Kbits/sec)
 
Diagnostic Function:
-Local loopback from SDH or E1 side
-Remote loopback from SDH or E1 side
-PRBS Pattern Test for E1 ports only(error rate
 
Management
-Easy to use Web UI configuration management
-SNMP v2 with Tainet UNMS
-Provide 5 SNMP trap IPs and read/write/trap community settings
-Support configuration upload/download and firmware update
 
Dimensions and Operating Environment
-MUXpro 820 =>210mm(W) x 285mm(D) x 41 mm(H)   
-MUXpro 8216 => 437mm(W) x 287mm(D) x 44 mm(H)   
-Operation temperature: 00C~ 500C  
-Storage temperature: -250C~ 700C  
-Relative humidity: up to 95% (non-condensing)
 
Power Requirement
-MUXpro 820   =>AC: 110V~240 +10V, 50~60+3Hz; DC: -36V ~ -72V
-MUXpro 8216  =>AC: 110V~240 +10V, 50~60+3Hz: DC: -36V ~ -72V (AC+DC / DC + DC)